三维钴基MOF[KCo7(OH)3(ip)6(H2O)4]·12H2O作为超级电容器的高容量电极材料

为了开发较高能量密度的超级电容器,我们通过简单的溶剂热反应合成了一种三维的钴基金属有机框架(MOF)化合物([KCo7(OH)3(ip)6(H2O)4]·12H2O,Co?ip;ip=间苯二甲酸根),并考察了其作为超级电容器电极材料的性能。Co?ip电极显示出高比电容、良好的循环稳定性和优良的倍率性能。在1 mol·L^-1 KOH溶液中,电流密度为1 A·g^-1时,其最大比电容为1660 F·g^-1。在电流密度为2 A·g^-1条件下,循环3000次后,其比电容的保持率为82.7%。优异的超级电容性能可归因于Co?ip具有纳米尺寸颗粒和三维的多孔结构。     

常见炸药的稳定同位素比值分析方法研究进展

炸药的深度比对与溯源对于爆炸案事件的侦破具有重大意义,以不同地域来源的原料或不同生产工艺生产的炸药,其组成元素的稳定同位素比值具有差异,因而稳定同位素比值可作为炸药深度比对与溯源的重要指标。稳定同位素比值质谱法(IRMS)作为一种高精度的稳定同位素比值测量手段,已逐渐发展成熟,与元素分析仪、气相色谱仪、液相色谱仪等仪器联用,在食品安全、环境保护、法庭科学等领域应用广泛。IRMS在炸药比对与溯源上亦发挥了重要作用,自1975年IRMS被应用于区分不同国家生产的三硝基甲苯(TNT)以来,IRMS已成功用于多种炸药的分析。但目前尚未见有文献系统地总结常见炸药的稳定同位素比值分析研究进展。该文介绍了稳定同位素比值分析的相关原理、仪器组成及特点,分别总结了硝酸铵、黑火药、TNT、太恩、黑索金等常见炸药的稳定同位素比值分析方法,汇总了文献报道的不同国家生产的硝酸铵、黑火药、TNT等炸药的稳定同位素比值。文章就不同炸药的稳定同位素比值差异、炸药生产、存储过程中相关因素对同位素比值的影响,爆炸前后稳定同位素比值的变化情况等内容进行了分析。本文还指出了目前炸药的稳定同位素比值分析研究中存在的问题,对可能的解决办法进行了讨论,对未来的发展方向提出了建议。     

作为表面增强拉曼光谱基底的高度均匀Au纳米棒的构筑及对福美双的检测

采用种子生长法制备Au纳米棒(GNRs),随后进行组装和煅烧得到单层致密堆积的GNRs薄膜。在煅烧过程中,组装所需有机物在煅烧过程中分解,从而使得GNRs表面具有较高的清洁度。研究中发现,煅烧前后金纳米棒表面的间隙进一步提高,增强了其SERS(表面增强拉曼光谱)活性。为了研究其SERS活性,选择了2种探针分子以研究其灵敏度和均匀性,发现其具有较高的灵敏度和高的信号稳定性。随后将所制备的SERS基底成功用于检测超低浓度的农药分子。     

BiVO4的添加对Nd0.2Ce0.8O1.9电解质微观结构和性能的影响

采用溶胶凝胶法制备BiVO₄（BV）和Nd_0.2Ce_0.8O_1.9（NDC）粉末,研究BV的加入对NDC电解质结构、形貌及电性能的影响。实验结果表明,NDC-5BV电解质的微观结构更致密,700℃时总电导率（σ_t）提高至3.35×10^-2 S·cm^-1,极化电阻（R_p）降低34%以上。单电池在700℃时的最大功率密度（MPD）为514 mW·cm^-2,开路电压（OCV）在70 h内可以保持良好的长期稳定性。     

La2-xBixCuO4阴极材料的合成与电化学性质

采用甘氨酸-硝酸盐法合成了固体氧化物燃料电池阴极材料La_2-xBi_xCuO₄（x=0、0.05、0.10）,并利用X射线衍射（XRD）对材料的物相进行分析。结果表明,La_2-xBi_xCuO₄形成单一的类钙钛矿结构氧化物,且晶胞体积随着铋掺杂量的增加而增大。在950℃烧结24 h过程中,La_2-xBi_xCuO₄不与电解质Sm_0.2Ce_0.8O_1.9（SDC）发生反应,表明这种电解质材料具有良好的高温化学相容性。电导率测试结果表明Bi的掺入显著提高了材料电导率。程序升温脱附测试结果表明,铋的掺杂显著增强了材料的表面氧吸附能力。不同氧分压下的交流阻抗谱测试结果表明,La_1.9Bi_0.1CuO₄阴极在700℃空气中的极化电阻为0.26 Ω·cm²,以电解质SDC支撑的单电池NiO-SDC/SDC/La_1.90Bi_0.10O₄在700℃的最大输出功率密度为308 mW·cm^-2,电极反应的速控步骤为氧分子的扩散与表面吸附过程。     

MnWO4/生物质衍生碳纳米复合催化剂的制备及催化性能

通过共沉淀法合成了双金属氧化物MnWO₄镶嵌生物质衍生碳（MnWO₄/BC）纳米复合催化剂,并将其作为对电极（counter electrode,CE）催化剂组装了染料敏化太阳能电池（dye-sensitized solar cell,DSSC）,探究了MnWO₄/BC在非碘体系中的催化性能和光伏性能。结果表明：在铜氧化还原（Cu²⁺/Cu⁺）电对DSSC中获得的光电能量转换效率（power conversion efficiency,PCE）为3.57%（D35）和1.59%（Y123）,高于Pt电极的PCE（3.12%,1.16%）;50次连续循环伏安测试表明,MnWO₄/BC催化剂具有较好的电化学稳定性。     

服役温度对多壁碳纳米管/Li1.18Ni0.15Co0.15Mn0.52O2复合正极材料性能的影响

通过煅烧的方式制得多壁碳纳米管(MWCNT)质量分数为3%的MWCNT/Li1.18Ni0.15Co0.15Mn0.52O2锂离子电池复合正极材料,并测试了复合正极材料在不同服役温度环境下的电化学性能:-20和60℃下服役时,其放电容量分别高达169、303 mAh·g^-1,且展示出良好的倍率性能和循环稳定性。结合电化学阻抗测试结果可知,MWCNT均匀附着在层状粒子的表面,有效减少了电解液对电极材料的侵蚀,阻碍了表面膜的生成,同时提高了材料的电子电导率。     

基于原位配体反应的锰(Ⅱ)配位聚合物的合成、结构和催化性质

采用水热方法,选用含2个氰基的醚氧桥联羧酸配体(Hdbna)和2,2′-联吡啶(2,2′-bipy)与MnCl2·4H2O反应,合成了一个二维配位聚合物[Mn(μ3-Hdpna)(2,2′-bipy)]n (1),并对其结构和催化性质进行了研究。在配合物1中,配体Hdbna在水热反应条件下,通过原位反应被转化成醚氧桥联三羧酸配体(H3dpna)。结构分析结果表明配合物1的晶体属于三斜晶系,P■空间群。配合物1具有二维层结构。研究表明,配合物1在硅腈化反应中表现出较高的催化活性。     

Needle-like cobalt phosphide arrays grown on carbon fiber cloth as a binder-free electrode with enhanced lithium storage performance

Cobalt phosphide(CoP) is a promising anode candidate for lithium-ion batteries(LIBs) due to its high specific capacity and low working potential.However,the poor cycling stability and rate performance,caused by low electrical conductivity and huge volume variation,impede the further practical application of CoP anode materials.Herein,we report an integrated binder-free electrode featuring needle-like CoP arrays grown on carbon fiber cloth(CC) for efficient lithium storage.The as-prepared CoP/CC electrode integrates the advantages of 1 D needle-like CoP arrays for efficient electrolyte wettability and fast cha rge transpo rtation,and 3 D CC substrate for superior mechanical stability,flexibility and high conductivity.As a result,the CoP/CC electrode delivers an initial specific capacity of 1283 mAh/g and initial Coulombic effeciencies of 85.4%,which are much higher than that of conventional CoP electrode.Notably,the Co P/CC electrode shows outstanding cycling performance up to 400 cycles at 0.5 A/cm² and excellent rate performance with a discharge capacity of 549 mAh/g even at 5 A/cm².This work demonstrates the great potential of integrated CoP/CC hybrid as efficient bind-free and freestanding electrode for LIBs and future flexible electronic devices.     

Adaptation of electrodes and printable gel polymer electrolytes for optimized fully organic batteries

Despite intensive scientific efforts on the development of organic batteries, their full potential is still not being realized. The individual components, such as electrode materials and electrolytes, are in most cases developed independently and are not adjusted to each other. In this context, we report on the performance optimization of a full-organic solid-state battery system by the mutual adaptation of the electrode materials and an ionic liquid (IL)-based gel polymer electrolyte (GPE). The formulation of the latter was designed for a one-step manufacturing approach and can be applied directly to the electrode surface, where it is UV-cured to yield the GPE without further post-treatment steps. Herein, a special focus was placed on the applicability in industrial processes. A first significant capacity increase was achieved by the incorporation of the IL into the electrode composite. Furthermore, the GPE composition was adapted applying acrylate- and methacrylate-based monomers and combinations thereof with the premise of a fast curing step. Furthermore, the amount of IL was varied, and all combinations were evaluated for their final performance in cells. The latter variation revealed that a high ionic conductivity is not the only determining factor for a good cell performance. Next to a sufficient conductivity, the interaction between electrode and electrolyte plays a key role for the cell performance as it enhances the accessibility of the counter ions to the redox-active sites.